Easy PDFs
Windows 10 & 11 Buy license · $59.95
Organize and print

How to Print a PDF as a Folded Booklet on Windows

Print a PDF as a booklet that folds in the right page order: duplex settings, flipping on the short edge, page counts and fixes for upside-down pages.

Updated 4 minute read The Easy PDFs team

To print a PDF as a booklet, choose a booklet print option so the pages are rearranged and printed two per side, then print double-sided with "flip on short edge". Fold the stack in half and the pages read in order. A booklet needs a page count that is a multiple of four, because each sheet of paper carries four pages; if yours isn't, blank pages are added at the end. If every other page comes out upside down, the printer is flipping on the long edge, so switch to short edge and print again.

This guide explains how booklet printing works, the settings to use on Windows, paper sizes, and how to fix the most common problems.

How booklet page order works

A booklet is not printed in normal page order. Each sheet holds two pages on the front and two on the back, and the sheets are nested inside each other before folding. For an 8-page booklet on two sheets, the layout is:

SheetFront (left, right)Back (left, right)
Sheet 1 (outside)8, 12, 7
Sheet 2 (inside)6, 34, 5

Working this out by hand is error-prone, which is why you should always use a booklet option rather than trying to rearrange pages yourself. The software calculates the order and scales each page to fit half a sheet.

Paper sizes and finished sizes

Each page is printed at half the sheet size, so plan for the finished size:

Paper you print onFinished booklet page
US Letter (8.5 × 11 in)5.5 × 8.5 in
US Legal (8.5 × 14 in)7 × 8.5 in
Tabloid (11 × 17 in)8.5 × 11 in (full Letter size)
A4A5

If your PDF has Letter pages and you print a booklet on Letter paper, every page is shrunk to about 65 percent. Text that was 11 point ends up around 7 point. For a readable booklet from Letter pages, print on Tabloid, or design the document at half-letter size from the start.

How to print a PDF as a booklet step by step

Easy PDFs can print all pages or a selection double-sided, as a booklet or several pages per sheet, with the margins and scaling you choose. The steps are:

  1. Open the PDF and check the page count. If it is not a multiple of 4, decide where blank pages should go. Usually the end is fine, but you may want a blank inside cover instead.
  2. Choose Print and select the booklet layout.
  3. Choose the paper size and check the preview: page 1 should be on the right half of the first sheet, with the last page on the left.
  4. Set double-sided printing to flip on short edge.
  5. Print one copy as a test, fold it and check the page order before printing the full run.

Many printer drivers also have their own booklet option under Printer Properties or Preferences. Use either the program's booklet option or the driver's, not both, or the pages get rearranged twice.

Short edge vs long edge

This is the setting that causes most booklet problems. In the Windows print dialog or your printer's preferences, two-sided printing has two options:

  • Flip on long edge turns the paper like a book page in portrait. Right for normal double-sided documents.
  • Flip on short edge turns the paper like a notepad. Right for booklets, because the booklet sheet is landscape.

If you pick long edge for a booklet, the back of every sheet comes out upside down relative to the front.

Printing a booklet without a duplex printer

If your printer can only print one side, use manual duplex:

  1. Choose the booklet layout and select manual double-sided or "print odd sides first" if offered.
  2. Print the fronts.
  3. Take the stack and put it back in the tray. Which way up and which way round depends on your printer, so mark the top of one sheet with a pencil dot on a test run to learn the right orientation.
  4. Print the backs.

Do one test sheet first. Getting the reload orientation wrong is the most common way to waste a whole run.

Fixing common booklet problems

Pages are in the wrong order after folding

Either the booklet layout wasn't used, or it was applied twice (once in the program and once in the driver). Turn one off.

The back side is upside down

Switch duplex to flip on short edge.

Pages look tiny

You are fitting full-size pages onto half sheets. Print on larger paper or accept the smaller size. Check the scaling is set to fit, not to a fixed small percentage.

Content is cut off near the fold

Increase the gutter or inside margin if your print settings offer one. If the PDF itself has text right up to the edge, there is not much room to work with.

Pages are rotated in the PDF

Mixed portrait and landscape pages print awkwardly in a booklet. Fix the orientation first; see how to rotate PDF pages and save them.

Nothing prints at all

That is a general printing problem rather than a booklet one. Work through why a PDF won't print first.

Tips for better booklets

  • Keep booklets to about 40 to 60 pages (10 to 15 sheets) for a simple fold and staple. Thicker booklets push the inner pages outward, an effect called creep.
  • Add blank pages deliberately so the back cover isn't a random content page. You can insert or rearrange pages first; see how to rearrange pages in a PDF.
  • Use heavier paper for the cover sheet if you print it separately.
  • Staple on the fold with a long-reach stapler, or use two staples about a quarter of the way from each end.

If you only need two or four pages on one side of a sheet, not a folded booklet, use the pages-per-sheet (n-up) option instead. Easy PDFs supports both, so handouts and booklets come from the same print dialog.

Frequently asked questions

Why are every other page upside down in my booklet?

The duplex setting is flipping on the wrong edge. For booklets, choose flip on short edge.

Does a booklet need a page count divisible by 4?

Yes, each folded sheet holds four pages. If your document is not a multiple of four, blank pages are added at the end.

Can I print a booklet without a duplex printer?

Yes, with manual duplex: print the front sides, put the stack back in the tray as instructed, then print the backs.

Get three guides like this every month, plus software update notices.Subscribe →